如果您對該產品感興趣的話,可以
產品名稱: Galil運動控制卡集成驅動器
產品型號: DMC-2143-DC24+AMP20540
產品展商: 美國Galil
產品文檔: 無相關文檔
簡單介紹
Galil運動控制卡集成驅動器，Galil DMC-2143-DC24可選端子板、驅動器等附件介紹。
Galil運動控制卡集成驅動器
的詳細介紹
|
Galil運動控制卡集成驅動器詳細說明
|
|
AMP20540
AMP-205x0 2- and 4-axis 500W Servo Drives：
The AMP-20540 contains four transconductance, PWM amplifiers for driving brushless or brush-type servo motors.Each amplifier drives motors operating at up to 7 Amps continuous, 10 Amps peak,18–60 VDC (available voltage at the motor is 10% less). The gain settings of the amplifier are user-programmable at 0.4 Amp/Volt, 0.7 Amp/Volt and 1 Amp/Volt.The switching frequency is 60 kHz.The
amplifier offers protection for over-voltage,under-voltage, over-current, short-circuit and over-temperature.Theamplifier status can be read through the DMC-21x3 controller, and the BS command allows easy hall sensor set-up.A 2-axis amplifier board
the AMP-20520 is also available. In a standard configuration the
DB-28040 I/O board will not install next to an AMP-20540, however the
AMP-20540 provides 8 uncommitted analog inputs with 12-bit ADC
(16-bit optional)
DMC-2143-DC24+AMP20440
|
Galil DMC-2143-DC24四軸運動控制卡可選的附件規格
|
|
|
|
|
|
端子板
|
ICM-20100
|
Provides D-sub connectors for cost-effective connection to external drives
|
|
ICM-20105
|
Provides D-sub connectors for interface to external drives in addition to optical isolation for inputs and outputs
|
|
ICM-20105T
|
Provides D-sub connectors for interface to external drives in addition to optical isolation for inputs and outputs
|
|
|
|
驅動器
|
AMP-20420
|
Contains two 200W PWM drives for driving brush-type servo motors
|
|
AMP-20440
|
Contains four 200W PWM drives for driving brush-type servo motors.
|
|
AMP-20341
|
Contains four small 20W linear drives for driving small brush-type servo motors
|
|
AMP-20520
|
Contains two 500W PWM drives for driving brushless or brush-type servo motors
|
|
AMP-20540
|
Contains four 500W PWM drives for driving brushless or brush-type servo motors
|
|
AMP-20542
|
Contains four PWM drives for driving brushless or brush-type servo motors(3Amps Continuous, 5Amps peak at 18-60VDC). Software selectable for low inductance motors .
|
|
SDM-20240
|
Contains four small drives for stepper motors operating in full/half step mode
|
|
SDM-20620
|
Contains two drives for stepper motors operating in microstepping mode
|
|
SDM-20640
|
Contains four drives for stepper motors operating in microstepping mode
|
|
|
|
附件
|
DB-28040
|
Provides 40 additional digital I/O and eight analog inputs
|
|
DB-28104
|
Provides sinusoidal interpolation for Sin/Cos encoders
|
|